| Range Of Product |
Altivar 12 |
| Product Or Component Type |
Variable speed drive |
| Product Destination |
Asynchronous motors |
| Product Specific Application |
Simple machine |
| Assembly Style |
On base plate |
| Component Name |
ATV12 |
| Quantity Per Set |
Set of 1 |
| Emc Filter |
Integrated |
| Built-In Fan |
Without |
| Network Number Of Phases |
1 phase |
| [Us] Rated Supply Voltage |
200...240 V - 15...10 % |
| Motor Power kW |
0.37 kW |
| Motor Power Hp |
0.55 hp |
| Communication Port Protocol |
Modbus |
| Line Current |
5.9 A 200 V
4.9 A 240 V |
| Speed Range |
1…20 |
| Transient Overtorque |
150…170 % of nominal motor torque depending on drive rating and type of motor |
| Async Motor Control Profile |
Sensorless flux vector control
Quadratic voltage/frequency ratio
Voltage/frequency ratio (V/f) |
| IP Degree Of Protection |
IP20 without blanking plate on upper part |
| Noise Level |
0 dB |
| Supply Frequency |
50/60 Hz +/- 5 % |
| Connector Type |
1 RJ45 on front face)Modbus |
| Physical Interface |
2-wire RS 485 Modbus |
| Transmission Frame |
RTU Modbus |
| Transmission Rate |
4800 bit/s
9600 bit/s
19200 bit/s
38400 bit/s |
| Number Of Addresses |
1…247 Modbus |
| Communication Service |
Read holding registers (03) 29 words
Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43) |
| Prospective Line Isc |
1 kA |
| Continuous Output Current |
2.4 A 4 kHz |
| Max Transient Current |
3.6 A 60 s |
| Speed Drive Output Frequency |
0.5…400 Hz |
| Nominal Switching Frequency |
4 kHz |
| Switching Frequency |
2...16 kHz adjustable
4...16 kHz with derating factor |
| Braking Torque |
Up to 70 % of nominal motor torque without braking resistor |
| Motor Slip Compensation |
Preset in factory
Adjustable |
| Output Voltage |
200...240 V 3 phase |
| Electrical Connection |
Terminal 3.5 mm², AWG 12 L1, L2, L3, U, V, W, PA, PC) |
| Tightening Torque |
7.08 lbf.in (0.8 N.m) |
| Insulation |
Electrical between power and control |
| Supply |
Internal supply for reference potentiometer 5 V DC 4.75…5.25 V), <10 mA overload and short-circuit protection
Internal supply for logic inputs 24 V DC 20.4…28.8 V), <100 mA overload and short-circuit protection |
| Analogue Input Number |
1 |
| Analogue Input Type |
Configurable current AI1 0...20 mA 250 Ohm
Configurable voltage AI1 0...10 V 30 kOhm
Configurable voltage AI1 0...5 V 30 kOhm |
| Discrete Input Number |
4 |
| Discrete Input Type |
Programmable LI1...LI4 24 V 18...30 V |
| Discrete Input Logic |
Negative logic (sink), > 16 V, < 10 V 3.5 kOhm
Positive logic (source), 0...< 5 V, > 11 V |
| Sampling Duration |
20 ms +/- 1 ms logic input
10 ms analogue input |
| Linearity Error |
+/- 0.3 % of maximum value analogue input |
| Analogue Output Number |
1 |
| Analogue Output Type |
AO1 software-configurable voltage 0...10 V 470 Ohm 8 bits
AO1 software-configurable current 0...20 mA 800 Ohm 8 bits |
| Discrete Output Number |
2 |
